Non asbestos Gery color High density Fireproofing Fiber Cement Board
Detailed Product Description
Fiber Cement Board is reinforced with selected fibers and fillers. It is mainly made from cement, quartz sand and reinforced fiber. It is free from inorganic fibers when formulated and does not contain formaldehyde. FC board is beige in color and has a smooth finish on one face with a dimple pattern on the other face. FC board provides with an architectural surface which is ready to receive most forms of decoration. It can be left undecorated and can be easily finished with paints and wallpapers for tiles. FC board is resistant to moisture and will not physically deteriorate when used in damp or humid conditions. Its performance will not be degraded by age or other negative factors.
100% free from asbestos.
Excellent Performance on water-proofing.
Excellent Performance on fire-proofing
|
Size (mm)
|
Thickness (mm)
|
Weight (KG)
|
Edge Profile
|
Application
|
|
1200 x 2400
1220 x 2440
|
4
|
18.00
18.61
|
Square-cut edge
|
Internal cladding
|
|
1200 x 2400
1220 x 2440
|
6
|
27.00
27.91
|
Square-cut edge/
Recessed edge
|
Internal/external ceiling
|
|
1200 x 2400
|
8
|
36.00
37.21
|
Square-cut edge/
Recessed edge
|
Internal partition
External wall cladding
Wet area and tile backing
Floor underlay
|
|
1200 x 2400
1220 x 2440
|
9,10
|
40.50
41.86
45.00
46.51
|
Square-cut edge
|
External wall cladding
Wet area and tile backing
Floor underlay
|
|
1200 x 2400
1220 x 2440
|
12
|
54.00
55.82
|
Square-cut edge/
Recessed edge
|
External wall cladding
Wet area and tile backing
Floor underlay
|
|
1200 x 2400
1220 x 2440
|
15
|
66.27
68.50
|
Square-cut edge
|
Internal partitions with special requirements
Elevated Floor
|
|
1200 x 2400
1220 x 2440
|
18
|
79.52
82.20
|
Square-cut edge
|
Internal partitions with special requirements
Elevated Floor
|
|
1200 x 2400
1220 x 2440
|
20
|
88.36
91.33
|
Square-cut edge
|
Internal partitions with special requirements
Elevated Floor
|
Tools:
No special tools are required. The products can be used with normal nails, fastened by normal or self-drilling screws and cut by an electric power saw with a diamond blade.
Fixing:
Sinoma Board can be fixed to both timber (minimum size 1.5 x 3 inches) or steel frames (at least 0.55 mm thickness). The board must be supported at the edge at intermediate positions with centers not exceeding 600 mm. Screws must be located more than 12 mm from edges and 50 mm from board corners.
Fastener:
Fasteners can be both nails and screws. It can be nailed directly to timber supports with round wire nails. For metal screws, the size and length of the screw depends on the thickness of the board and the gauge of framing.
Jointing:
Since fiber-cement board is subject to slight dimensional changes, a butt joint can be used in dry partitioning areas or where an exposed joint appearance is acceptable. For better water protection, either flexible acrylic or polyurethane based sealant can be used to seal gaps of 3-5mm.
Transportation, Handing and Storage:
Deliver SINOMA Board to the project site in the original, unopened package and store them in fully enclosed space where they will be protected against damage from humidity, direct sunlight, surface contamination and other causes of damage. Handle SINOMA Board carefully to avoid chipping the edges or damaging units in any way. Handling and storage practices should follow the manufacturer’s recommended suggestions at all times.
Product Tags:
|
|
Gery Color Exterior Fibre Cement Cladding , 10 Mm Fibre Cement Sheet No Deformation Images
|
